Schneider Electric

ATV61HC13N4D

ATV61HC13N4D Schneider Electric

The product image shown is for illustration purposes only and may not be an exact representation of the product. Please refer to the item description for accurate information

Please note: Some products are subject to manufacturer minimum pack quantities. We will confirm this at time of order.

Description for ATV61HC13N4D Schneider Electric

ATV61HC13N4D Schneider Electric - SPEED DRIVE,200HP,460V,ATV61-NO DC CHOKE

Free Delivery to UK Mainland on orders over £25

Manufacturer New

Available for Back Order
£9,134.62 Exc. VAT
£10,961.54 Inc. VAT

Direct from Manufacturer

Available on back order
4 - 6 W.Weeks
£7,448.39 Exc. VAT
£8,938.07 Inc. VAT

Main

range of product Altivar 61
product or component type Variable speed drive
Product specific application Pumping and ventilation machine
Component name ATV61
Motor power kW 132 kW, 3 phases at 380...480 V
Motor power hp 200 hp, 3 phases at 380...480 V
power supply voltage 380...480 V - 15...10 %
supply number of phases 3 phases
Line current 224 A for 480 V 3 phases 132 kW / 200 hp,239 A for 380 V 3 phases 132 kW / 200 hp
EMC filter Level 3 EMC filter
Variant Without DC choke
Assembly style With heat sink
Apparent power 157.3 kVA at 380 V 3 phases 132 kW / 200 hp
maximum prospective line Isc 35 kA for 3 phases
Maximum transient current 310.8 A for 60 s, 3 phases
Nominal switching frequency 2.5 kHz
Switching frequency 2...8 kHz adjustable,2.5...8 kHz with derating factor
asynchronous motor control Voltage/frequency ratio, 2 points,Flux vector control without sensor, standard,Voltage/frequency ratio, 5 points,Voltage/frequency ratio - Energy Saving, quadratic U/f
Synchronous motor control profile Vector control without sensor, standard
communication port protocol CANopen,Modbus
Type of polarization No impedance for Modbus
Option card Communication card for APOGEE FLN,Communication card for BACnet,Communication card for CC-Link,Controller inside programmable card,Communication card for DeviceNet,Communication card for EtherNet/IP,Communication card for Fipio,I/O extension card,Communication card for Interbus-S,Communication card for LonWorks,Communication card for METASYS N2,Communication card for Modbus Plus,Communication card for Modbus TCP,Communication card for Modbus/Uni-Telway,Multi-pump card,Communication card for Profibus DP,Communication card for Profibus DP V1

Complementary

Product destination Synchronous motors,Asynchronous motors
power supply voltage limits 323…528 V
power supply frequency 50...60 Hz - 5...5 %
power supply frequency limits 47.5...63 Hz
Continuous output current 259 A at 2.5 kHz, 380 V - 3 phases,259 A at 2.5 kHz, 460 V - 3 phases
Output frequency 0.1…500 Hz
Speed range 1…100 in open-loop mode, without speed feedback
Speed accuracy +/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback
Torque accuracy +/- 15 % in open-loop mode, without speed feedback
Transient overtorque 130 % of nominal motor torque +/- 10 % for 60 s
Braking torque <= 125 % with braking resistor,30 % without braking resistor
Regulation loop Frequency PI regulator
Motor slip compensation Automatic whatever the load,Adjustable,Can be suppressed,Not available in voltage/frequency ratio (2 or 5 points)
diagnostic 1 LED (red) for drive voltage
Output voltage <= power supply voltage
electrical isolation Between power and control terminals
type of cable for mounting in an enclosure With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC,With UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC,Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC,Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR
Electrical connection Terminal 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR),Terminal 2 x 100 mm² / 2 x 250 kcmil (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3),Terminal 60 mm² / 250 kcmil (PA, PB),Terminal 2 x 150 mm² / 2 x 250 kcmil (PC/-, PO, PA/+)
Tightening torque 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR),24 N.m, 212 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3),41 N.m, 360 lb.in (PC/-, PO, PA/+),12 N.m, 106 lb.in (PA, PB)
Supply Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC, +/- 5 %, <10 mA with overload and short-circuit protection,Internal supply: 24 V DC (21…27 V), <200 mA with overload and short-circuit protection,External supply: 24 V DC (19…30 V)
Analogue input number 2
Analogue input type AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign,AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits,AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits
sampling time 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input,2 ms +/- 0.5 ms (Al2) - analog input,2 ms +/- 0.5 ms (AO1) - analog output,2 ms +/- 0.5 ms (LI1...LI5) - discrete input,2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input
absolute accuracy precision +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C,+/- 0.6 % (AI2) for a temperature variation 60 °C,+/- 1 % (AO1) for a temperature variation 60 °C
Linearity error +/- 0.15 % of maximum value (AI1-/Al1+),+/- 0.15 % of maximum value (AI2),+/- 0.2 % (AO1)
Analogue output number 1
Analogue output type AO1 software-configurable current, analogue output range 0...20 mA, impedance: 500 Ohm, resolution 10 bits,AO1 software-configurable voltage, analogue output range 0...10 V DC, impedance: 470 Ohm, resolution 10 bits,AO1 software-configurable logic output 10 V, 20 mA
Discrete output number 2
Discrete output type Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles,Configurable relay logic: (R2A, R2B) NO - 100000 cycles
maximum response time <= 100 ms in STO (Safe Torque Off),R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms,R2A, R2B <= 7 ms, tolerance +/- 0.5 ms
Minimum switching current 3 mA at 24 V DC for configurable relay logic
Maximum switching current R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms,R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms,R1, R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms,R1, R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms
Discrete input number 7
Discrete input type Programmable (LI1...LI5)24 V DC (<= 30 V), with level 1 PLC - 3500 Ohm,Switch-configurable (LI6)24 V DC (<= 30 V), with level 1 PLC - 3500 Ohm,Switch-configurable PTC probe (LI6)0…6 probes - 1500 Ohm,Safety input (PWR)24 V DC (<= 30 V) - 1500 Ohm
Discrete input logic Negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1),Positive logic (source) (LI1...LI5), < 5 V (state 0), > 11 V (state 1),Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1),Positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1)
Acceleration and deceleration ramps S, U or customized,Automatic adaptation of ramp if braking capacity exceeded, by using resistor,Linear adjustable separately from 0.01 to 9000 s
Braking to standstill By DC injection
Protection type Against exceeding limit speed: drive,Against input phase loss: drive,Break on the control circuit: drive,Input phase breaks: drive,Line supply overvoltage: drive,Line supply undervoltage: drive,Overcurrent between output phases and earth: drive,Overheating protection: drive,Overvoltages on the DC bus: drive,Power removal: drive,Short-circuit between motor phases: drive,Thermal protection: drive,Motor phase break: motor,Power removal: motor,Thermal protection: motor
Insulation resistance > 1 mOhm 500 V DC for 1 minute to earth
Frequency resolution Analog input: 0.024/50 Hz,Display unit: 0.1 Hz
Connector type 1 RJ45 (on front face) for Modbus,1 RJ45 (on terminal) for Modbus,Male SUB-D 9 on RJ45 for CANopen
Physical interface 2-wire RS 485 for Modbus
Transmission frame RTU for Modbus
Transmission rate 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal,9600 bps, 19200 bps for Modbus on front face,20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
Data format 8 bits, 1 stop, even parity for Modbus on front face,8 bits, odd even or no configurable parity for Modbus on terminal
Number of addresses 1…127 for CANopen,1…247 for Modbus
Method of access Slave CANopen
marking CE
Operating position Vertical +/- 10 degree
net weight 74 kg
Width 360 mm
Height 782 mm
Depth 377 mm

Environment

Noise level 69.5 dB conforming to 86/188/EEC
Dielectric strength 3535 V DC between earth and power terminals,5092 V DC between control and power terminals
Electromagnetic compatibility Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6,Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4,Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2,Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3,Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
Standards EN 61800-3 environments 1 category C3,IEC 60721-3-3 class 3C2,EN 55011 class A group 2,EN/IEC 61800-3,UL Type 1,EN/IEC 61800-5-1,EN 61800-3 environments 2 category C3
Product certifications CSA,NOM 117,C-Tick,UL,DNV,GOST
Pollution degree 3 conforming to EN/IEC 61800-5-1,3 conforming to UL 840
degree of proctection IP41 on upper part conforming to EN/IEC 60529,IP41 on upper part conforming to EN/IEC 61800-5-1,IP54 on lower part conforming to EN/IEC 60529,IP54 on lower part conforming to EN/IEC 61800-5-1,IP00 conforming to EN/IEC 60529,IP00 conforming to EN/IEC 61800-5-1,IP30 on side parts conforming to EN/IEC 60529,IP30 on side parts conforming to EN/IEC 61800-5-1,IP30 on the front panel conforming to EN/IEC 60529,IP30 on the front panel conforming to EN/IEC 61800-5-1
Vibration resistance 0.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-6,1.5 mm peak to peak (f= 3…10 Hz) conforming to EN/IEC 60068-2-6
Shock resistance 7 gn for 11 ms conforming to EN/IEC 60068-2-27
Relative humidity 5…95 % without condensation conforming to IEC 60068-2-3,5…95 % without dripping water conforming to IEC 60068-2-3
Ambient air temperature for operation -10…45 °C (without derating),45…60 °C (with derating factor)
Ambient air temperature for storage -25…70 °C
Operating altitude <= 1000 m without derating,1000...3000 m with current derating 1 % per 100 m

Packing Units

Unit Type of Package 1 PCE
Number of Units in Package 1 1
Package 1 Height 53.0 cm
Package 1 Width 41.5 cm
Package 1 Length 123.0 cm
Package 1 Weight 122.0 kg
Unit Type of Package 2 CAR
Number of Units in Package 2 1
Package 2 Height 53.0 cm
Package 2 Width 41.5 cm
Package 2 Length 123.0 cm
Package 2 Weight 122.0 kg
Unit Type of Package 3 PAL
Number of Units in Package 3 1
Package 3 Height 53.0 cm
Package 3 Width 41.5 cm
Package 3 Length 125.0 cm
Package 3 Weight 123.0 kg

Contractual warranty

Warranty 18 months

Documentation

Product Datasheet

User guide

Instruction sheet

Catalogue

CAD

Looking for a specific part?

If the product you're searching for isn't listed, click below to submit your enquiry and one of our specialists will source it for you.

CTA image

Contact Us

Using one of the ways below contact us and we will get back to you as soon as possible

Whatsapp
Web Form Phone Email More details